A few things you don't know about beauty joints-beauty joints factory

、Can any ceramic tiles be beautifully stitched? Are there any requirements? Answer: There needs to be a certain gap to make the beautiful seam of ceramic tiles. If it is seamless splicing, the beautiful seam cannot be made without a certain bonding space, so seamlessly spliced u200bu200btiles cannot be made beautiful seams. 、Does the joint of ceramic tile need grout for primer? Answer: It is similar to the answer to the previous question. It also needs to be considered from the cost and the degree of adhesion. Generally, it is better to use a sealant as a primer and leave a seam depth of about mm, so that it can maintain a good value while considering the cost. Using time, if cost factors are not taken into consideration, and no caulking agent is used for primer, the bonding degree will be maintained for a longer period of time. , After the two-component beauty seam agent is applied, some places do not dry, how long will it take? Answer: If there is still a part of the two-component seam agent that does not dry after an hour after the application, the main reason is that the epoxy resin and the curing agent are not completely mixed, resulting in no drying. Generally, there is no need to wait in this case, because this It is impossible to dry the situation anymore. You can only buckle up the ones that do not dry and re-construct. This is a normal phenomenon of two-component beauty joints. It is recommended not to finish the construction at one time, leaving some remaining material for repair. , Is the hardness of the two-component beauty joint agent the higher the better? Answer: In terms of hardness, the harder the better, it should be soft and rigid, like iron wire, it not only has the same hardness as iron, but also has good toughness. 、Does the two-component beauty jointing agent have to be covered with textured paper when encountering antique bricks, matt bricks, and rough-faced bricks? Answer: At present, there are two practical methods for the construction of rough-faced bricks such as antique bricks and matt bricks. One is the water-based epoxy resin material beauty joint agent represented by the beauty joint agent factory, which can realize the water rubbing operation. The other is to use the beauty seam partner, which can effectively prevent the penetration of the two-component beauty seam agent and realize the residual problem of the two-component beauty seam agent on both sides of the tile. 、Whether the construction of the two-component beauty joint agent is scraped with a scraper? Or use the sewing ball to press it? Answer: If you use a scraper to scrape, then after the scraper is finished, the beauty joint and the gap will be flat. In this way, the scratching in daily life is unavoidable, and the accumulation of time will easily cause the gloss to decrease. If you use a press ball, there will be micro grooves in the gap to prevent scratching in daily life. 、Is it possible to use powder as a primer instead of caulking agent? Answer: No, after injecting the beauty grout, powdery dust such as cement powder will be wrapped around the beauty grout, causing it to not be able to bond with the gap, so be sure to keep the gap clean. 、Is it okay to find that the sealant is wet before making beautiful seams? Answer, no. Because if the caulk is wet, its water vapor evaporates and penetrates into the caulking agent, changing the molecular structure of the caulking agent, especially the two-component caulking agent. The water vapor will make the curing agent ineffective. If it is in the bathroom, because The lower layer is waterproof. The last time the beautifier is also waterproof, it will cause the beautifier to top out, so be sure to keep the grout dry and the gap dry. , How to choose beauty seam agent? Is the quality of the beauty stitches on the market the same? Answer: After more than ten years of development, single-component beauty joints have developed into a bottleneck that is difficult to break through. Simply put, the choice of single-component beauty joints mainly focuses on the consistency and viscosity of their products. Generally, the difference is not very big. Two-component beauty joints are mainly inspected from the raw materials and production technology of the products. For example, the beauty joints factory uses imported raw materials from Germany, so the quality of the beauty joints is not the same. , What are the mainstream classifications of beauty seams now? What are the advantages and disadvantages of each? Answer: The more mainstream beautifying agents on the market are mainly divided into single-component beautifying agents and two-component beautifying agents. Single-component beautifying agents are processed by polymer nanometer and pigments, which is an earlier beauty. The advantages of the types of sewing products are simple, fast and convenient construction. The disadvantage is that the hardness and color are slightly inferior to the two-component beautifying agent. The two-component beautifying agent is processed by epoxy resin, curing agent and pigment. The advantages are It has the advantages of high hardness, good gloss and long retention period, but the disadvantage is that the construction is relatively cumbersome.
Beauty Seam Agent