After reading these 4 articles, you don’t have to worry about the rework of the beauty joint construction! -Beautiful seam agent factory

Tile beautiful seam has become an important decoration project, so it is particularly important in the process of construction and acceptance. Whether you hire a professional construction team or plan to do your own DIY construction, you don't want to encounter troublesome things like rework, which will waste time and delay the construction period, and waste energy and money. In order to avoid rework, we must pay attention to details and be careful. Today, we will bring you common quality problems and solutions, so you never have to worry about rework! Question 1: The color is paler than the original, and it looks like a white mist. The cause of the problem: () The environmental humidity is too high. () Moisture is mixed in the construction surface, container, crevice, and beautifying agent. () The water contained in the bottom sealant has not been removed. () Use a poor beauty seam agent because it turns white due to transparency problems. Solution: () Dry treatment before construction. () Do not apply when the humidity is high. () The construction surface should be clean and free from moisture. () The bottom caulking agent or the water in the gap of the tiles should be dried. () Choose good quality beauty seam products. Problem two due to poor adhesion and bonding, there will be peeling, peeling, bulging, peeling and other phenomena. The cause of the problem: () The sealant is inferior, resulting in poor adhesion between layers. The sealant used for the primer is too dry, or even in a powder state, and it has strong water absorption. If it encounters a thinner beautifying layer, it will often seriously affect the curing effect and cohesiveness of the beautifying agent. , So that the construction surface peels and falls off. () The crevices are dirty, stained with oil, water or other dirt. () Use inferior beauty joint agent () The construction temperature is too low. Solution: () Choose a good quality sealant for primer. () When treating the surface of the substrate, the oil, moisture or other dirt should be completely removed. () Choose high-quality beauty seam agent, Shangsil real porcelain has strong bonding force, does not fall off, and does not collapse! Question 3 After a period of time, it is still not dry and does not harden. The cause of the problem: () A/B two components are not uniformly mixed. () Throw away the material that has not been hit by centimeters at the front end during construction. When a new material is first used to hit the two tubes A and B with a glue gun, one side will always come out first. At this time, the material is not uniformly mixed (that is, there is no: mixing). If the waste material of this centimeter is not thrown away, it will be hit in the seam Cause the product to not cure. () When workers are filling, air will occasionally enter the hose, causing the capacity ratio of the AB group to be out of balance. In this case, intermittent non-curing or partial non-curing will also occur. () After the centimeter of the material is shot out and thrown away, if the opening of the mixing tube is too small, it will also cause the ejected material to be in an unmixed state after the centimeter is thrown away. Solution: () Construct according to correct construction requirements. () The opening of the mixing tube is opened as required. () One mixing tube is equipped with one beautiful seam agent. Problem four causes flow and uneven thickness. Reasons: () The width of the tile joint is within the range of -mm, which is a normal beautiful joint. The product can be used directly. If the tile joint is out of this range, it is recommended to do it after bottoming. It is recommended to use a white base, white will not affect the color of the seam agent. () The temperature of the construction site is too low, causing the material to shrink. At this time, the beauty joint agent is generally heated appropriately, and the temperature is too high during the heating process, which will cause the material in the beauty joint agent hose to become thin. () The high temperature in summer may also cause the material to become thinner. () The unevenness of the spraying surface or the grooves of the edges, corners, and line corners of the object can easily cause uneven spraying and uneven thickness, and the thicker parts will flow. () When the material is beaten too fast or too thin during construction, different degrees of dents will appear. Solution: () The temperature and humidity of the construction environment are appropriate. () It is recommended not to press the seam immediately after the material is laid. It is recommended to use the press seam ball to press the seam after the material is laid. () Put the product in a cool and dry place. () When the beauty seam agent is properly heated, the temperature should be controlled at about °.
Beautiful Seam Construction Tile Beautiful Seam