Ceramic tile adhesive for your life add color

Glue can be divided into many types, but using the corresponding glue in different industries. Such as ceramic tile, ceramic tile is inseparable from the most when ceramic tile adhesive, ceramic tile adhesive, also known as ceramic tile adhesive, it can make is widely applied in all kinds of wall brick, floor tile, etc. Here we introduce the relevant information of ceramic tile adhesive, want to know the friend brand ceramic tile adhesive can want to see! 1, ceramic tile adhesive is introduced ceramic tile adhesive because of its high bonding strength, water resistance, freeze-thaw resistance, ageing resistance and the advantages of the construction is convenient to replace the traditional cement sand, its adhesive bond is several times of cement mortar, is widely used in all kinds of inside and outside wall, floor, bathroom, kitchen, such as construction sites. Ceramic tile adhesive is divided into three types: A, no. 1 as the ordinary ceramic tile adhesive, applicable to all to paste on the surface of the ordinary mortar or metope brick material small brick material; B, no. 2 for enhanced ceramic tile adhesive, it has strong cohesive force and sag resistance, can use for big bond demand on the surface of the metope ceramic tile, the mortar paste, such as wood, etc. Ceramic tile adhesive, also known as ceramic tile adhesive or adhesive, adhesive cement, such as multiple names, is a modern decoration of new materials, replacing the traditional cement sand, glue bond is several times of cement mortar can effectively stickup ceramic tile of large stone, avoid the risk of falling bricks. Good flexibility, prevent the production of empty drum. This product is a kind of polymer modified cement base ceramic tile adhesive, divided into 1 ( Ordinary) , no. 2 ( Enhanced) And 3 ( Heavy brick type) Other varieties. No. 1 on the surface of the ceramic tile adhesive is suitable for ordinary mortar various ground brick material or small brick wall material paste; 2 ceramic tile adhesive with strong cohesive force and sag resistance, applicable for larger metope ceramic tile, the requirements for bond mortar surface such as wooden plank surface or old veneer paste; Ceramic tile adhesive bond 3 big, more flexibility, can resist heat bilges cold shrink stress, bonding layer is suitable for ceramic tile paste in gypsum board, fiberboard, plywood or veneer (old Ceramic tile, Mosaic, terrazzo) As well as larger size paste of various kinds of stone slab. Ceramic tile adhesive in addition to the gray, also can provide with white appearance, suitable for light or translucent marble, ceramic tile, and other natural stone. Construction method 1, the surface treatment of all surfaces should be solid, dry, clean, no shaking, no oil, wax stains and other loose materials; Painted surface roughening treatment should be done, exposed to at least 75% of the original surface; After the completion of the new concrete surface, need maintenance six Zhou Fangke tiles, a new plaster surface should be maintained at least seven out of tiles; The old concrete and plaster surface can use detergent to clean, and then rinse clean with water. The dry rear can brick paving on the surface; Substrate osteoporosis, water imbibition is strong or surface dust dirt is difficult to clean, can besmear first LeiBangShi bottom oil to help ceramic tile adhesive. 2, will TT powder into the mixing water in mix into a paste and pay attention to the water before they are put on powder. When can use manual or electric blender; Mixing proportion is around 6 ~ 25 kg powder and water. 5 kg; Available when necessary the company LeiBangShi ceramic tile additive instead of water, the ratio of 25 kg powder doping 6. 5 to 7. 5 kilograms; Stir fully, will be subject to no raw glutinous rice dough. Mixing must still placed slightly after about ten minutes after a stir before use; Mucilage should be controlled according to the weather conditions in about 2 hours after use, Mucilage surface crust should remove without) 。 Don't will have hard mucilage reoccupy after adding water. 3, construction technology and the mucilage with tooth type scraper daub on face, evenly distributed, and into strips dentate ( Adjust the scraper and face Angle to control the thickness of mucilage) 。 Each coating about 1 square metre ( Depending on the weather temperature, construction temperature range required for 5 ~ 40 ℃) And then in 5 ~ 15 minutes to get ceramic tile on the pressure in ( Adjustment should be carried out in 20 ~ 25 minutes) ; Choose tooth type scraper size ceramic tile work surface roughness and should be considered in the back of the intensive degree; Such as ceramic tile on the back of the groove gap deeper or stone material, ceramic tile is bigger, the two-sided glue, should be implemented in the working face and the ceramic tile on the back of the coated with rubber paste at the same time; Pay attention to keep expansion joint; After completion of tiles, when the mucilage completely dry solid ( About 24 hours) To take the next step of caulking process; Before dry solid ceramic tile surface with a damp cloth or sponge ( And tools) Clean up. If cure more than 24 hours, stains on the surface of the ceramic tile ceramic tile stone cleaner for cleaning ( Do not use acidic cleaner) 。