Ceramic tile is the seam construction process is introduced

Now many ceramic tile all did the seam in the home, looking for the master of professional beauty do ceramic tile seam is not low price, so many want to save decorate owner would consider modernize diy ceramic tile seam. If you decide to do the seam, and want to do your own, congratulations you just saved thousands. Ceramic tile seam beauty said simple simple also, according to specifications. But if I want to be beautiful, there is no certain experience are still a little difficult to do well.

the ceramic tile seam construction process

1. Processing: brick joints can caulking can not fill in, such as caulking need caulking material completely dry, can undertake the seam an agent construction, seam deep minimum is about 3 mm;

2, cleaning: use should be taken before the seam an agent to clean dust with a vacuum cleaner to suck in the ceramic tile aperture, ceramic tile seam on both sides of the towel clean, remove dust, grease and other pollutants, at the same time with clean shovel to remove contaminants on the surface of the ceramic tile.

3, stick: crepe paper if the ceramic tile of archaize brick or pits brick, crepe paper, before the seam surface brick can not stick. Posted when the crepe paper, on the surface of the ceramic tile aperture should keep clean and dry. Crepe paper to stick a side of the gap, in order to guarantee the effect of cross intersections, somehow the line construction Suggestions separated for 24 hours a day. On either side of the crepe paper will cut neatly without burrs, width is not less than 2 cm, stick relay is better but not residual glue.

4, grab a seam: choose to color of true porcelain glue, set up the special mixing tube, put on special high quality energy glue gun, squeeze to remove the front 30 g true porcelain glue, make true porcelain glue mixture fully. Mixing tube as possible at the seam vertical to true porcelain and ceramic tile surface glue fills gaps, while walking even, good grasp of the intensity and frequency so that the true porcelain out the glue. 5 - appropriate temperature 38 degrees.

5, seam pressure rave: if you want to make a true porcelain adhesive cured surface can moderate the circular arc surface, can use special pressure seam steel ball from brick force along the seam at one end to the other side, hard to maintain uniform, If you want true porcelain and ceramic tile adhesive cured performance surface as far as possible in a horizontal plane, can use the seam scraper or soft rubber sheet from brick force along the seam at one end to the other end, maintain strength, and do not deviate from the crepe paper to prevent pollution of ceramic tile surface.

6, cleaning, such as adopting the technology of crepe paper, let stand for 5 - 10 minutes. Tear the paper to remove the surrounding beauty true porcelain adhesive seam an agent, wipe the stains. If use of technology of crepe paper, will have to wait until after seam about 3 hours, with clean shovel half solidification of true porcelain glue of ceramic tile surface clean.

7, finished product protection: normal temperature below 25 degrees, table 3 hours, 24 hours using strength, natural curing 7 days. Within 24 hours after the seam to avoid contamination, rain, water, avoid walking on the ground.

the seam an agent construction matters needing attention

1, the rubber mouth opening with a knife, be sure to cut the right size. Drive hole is too small and beautiful seam an agent played too slow; Open too big hole, hit the beauty of the seam an agent is too much, cause waste, still not clear. Suggested that start with a smaller aperture, according to the crack depth increased slowly.

2, cement must be aligned cracks. When playing, a direction as far as possible. Such as the finish line first, and then to make a vertical bar.

3, beautiful seam an agent is quick-drying type, rubber mouth every time want to use wet cloth to wipe, otherwise the hole is blocked was in trouble.

although the process is not complicated, but pay attention to detail each step of the way. Fire makes sweet malt, do not over a day is normal, can divide a shard between OuDeMei seam, both to moderate degree of fatigue, also can ensure the quality and effect.