loading

Professional manufacturer of tile grout and adhesives with 27 years experience

Decorated in ceramic tile acceptance - after the completion of the shop is stuck Ceramic tile adhesive | | | waterproof coating straight with mortar jointing agent

many workers to stick at home after good ceramic tile, tend to look simple, feel there is no problem with respect to OK, in fact this is not standard. Because ceramic tile is not good, is likely to be in the later will cause uneven, even fall off wait for a phenomenon, so everyone in ceramic tile after the shop is stuck, must carefully check acceptance, mainly includes two aspects. Ceramic tile shop sticks a visual inspection of ceramic tile is common in domestic outfit in the bathroom wall ground and place such as sitting room ground, as an important one of the 'face' of home, ceramic tile shop sticks after first need to check is the appearance of it. First check, check whether comply with the design requirements of ceramic tile shop sticks according to the request of design, such as asking for is the diamond inclined shop owner, it will not be able to shop USES a horizontal or vertical laying method. In addition to the shop is stuck method, check the tile shop sticks direction is correct, with or without inversion phenomenon; Tile and the waist position is correct, if there's any deviation or height error, and so on and so forth. And see if any scratches gaps in the process of the ceramic tile shop is stuck, easy scratches or damage due to careless construction ceramic tile. Acceptance, be the first to see whether any scratches or difficult to remove the stain on the surface of the ceramic tile, brick surface for signs of the crushing collapse Angle, etc. , see if any crack crack usually selected during the day light cases, to see and touch the method, to check whether there is crack brick surface cracks. Crack is refers to the tile surface crack, but the bottom of the ceramic tile is in good condition, slight cut hand touch feel; Crack is refers to the whole brick from the surface to the bottom surface cracking, touch feel obviously hand cut. , see if gap evenly to cope with the problem of heat bilges cold shrink ceramic tile, and ensure the effect of ceramic tile shop sticks straight, in shop sticks ceramic tile, brick and tile between need to seam. Need to check whether the ceramic tile aperture is even beautiful, when acceptance of general brick joints for mm wide, cannot exceed the mm. Special effects can also be gap widened, such as mm. Also, check if ceramic tile edge or sealed. Check horizontal flat vertical and sloping tile pavement smoothness and verticality check is necessary, because if the shop sticks ceramic tile, on the one hand, affect beautiful, on the other hand will influence the furniture put, make it appear not tight against the wall or put the uneven phenomenon. How to check the flatness of ceramic tile? It's need with the help of flatness inspection tools. , verticality between bath and kitchen metope ceramic tile on the shop usually, at this moment need to check whether horizontal flat vertical metope. We first take a look at how to check the tile facade of verticality. Check whether the vertical can use M on foot, but can't accurate measurement deviation, while using the M vertical detection ruler can detect the deviation. Ruler on the left side of the vertical detected by the measured surface, and then after being pointer to stop oscillating, read Pointers scale values, the value that is measured surface verticality deviation, each for mm. The facade of ceramic tile verticality will make the mm or less. Ceramic tile smoothness, flatness detection tests, can use vertical inspection rule, also can use M on feet and wedge feeler detection. After using a method of detecting, will by feet side by the measured surface, the aperture size by wedge feeler detection. Each test three points should be, that is, vertical, and in the in situ each cross °, pick up three points average. Ceramic tile flatness error must not exceed ㎜, adjacent brick elevation difference should not exceed. ㎜. , Yin and Yang Angle founder degrees check the metope ceramic tile shop is stuck, existence of Yin and Yang Angle, need to use a square of Yin and Yang to detect all the Yin and Yang Angle founder degrees, according to the national request of Yin and Yang Angle deviation is no more than mm. Test, open the feet, with two portable meters to be Yang Angle two sides, see its scale pointer, when in the '', explains founder degrees for °, namely reading is' '; When the scale pointer to the 'left' deviation, that Angle is greater than the °; When the scale pointer to the 'left' deviation, that Angle is less than °, deviating from the several case, is the error of a few millimeters. , slope gradient inspection mainly involves is the floor tile shop is stuck, between wei yu, balcony and the kitchen floor tile should be enough since the drainage slope of the floor drain. Slope should meet the requirements of flood water, water. Acceptance of floor tile must try water, especially in a bathroom, kitchen, tilt to the floor drain, so that water is flowing fast and drainage fast. Check to see if the ground water flow quickly, at the same time, look for the ceramic tile whether leakage has occurred. Several times when check whether the ground leakage, it is suggested that water, water observation after a period of time.

GET IN TOUCH WITH Us
recommended articles
Knowledge APPLICATION NEWS
Sealant Composition and Function

Sealants are commonly used in construction and home improvement projects to fill gaps and cracks, providing a watertight and airtight seal.
Every successful project needs purpose-built solutions to ensure efficiency, effectiveness, and overall success.
Contact Adhesive Safety Guidelines: What to Follow

Contact adhesive is a versatile and widely used adhesive that is commonly used for bonding materials such as wood, metal, and plastic.




What is Contact Adhesive?

Contact adhesive is a type of adhesive that is widely used for flexible bonding applications.
In today's highly competitive market, businesses are constantly looking for ways to bring innovative products to market faster and more efficiently.
no data

Contact Us

Whatsapp : +86 13924533378
Wechat : +86 13924533378
Tel : +86 731 89870169
E-mail : sales@kastarsealant.com
Address: No.1, ShunJing Road, Songxia Industrial Park, SongGang Town, Foshan, China

Better Touch Better Business

Contact Sales at Kastar.

Call Us

+86 13924533378

Copyright © 2025 Kastar adhesive Co.,Ltd. | Sitemap
Customer service
detect