The construction joints, encounter bumps and bubble, what shall we do?

The Chinese New Year is coming soon, the owners of rob before Chinese New Year to finish the renovation as soon as possible, good comfortable enjoy the Spring Festival. So winter until the end of this period of time the owner will be a big demand for the joint business. But in winter the environment greatly increased the difficulty of the seam, before we have introduced some of the winter should pay attention to the construction of local, today we went on to look at the beautiful stitch encounter in the process of & other; Bump and bubble & throughout; Problems, and the prevention and solution.

first of all, let's see what the situation will bump and bubble:

ceramic tile aperture is moisture ( Beautiful seam construction must be dry and clean environment, this is stressed, every article again) As the moisture evaporation, can lead to the seam gas bubbles.

with ash of ceramic tile aperture, not clean. Ceramic filled seam an grout before curing belong to liquid, after precipitation type leads to uneven glue.

ceramic tile aperture is too small, the construction speed is quick, pause or glue will start construction fast, glue did not enter inside crack, and on the surface, causing gas underneath, behind the seam pressure inside the gas can't discharge, can lead to colloid appear bubbles.

ceramic caulking gun construction thickness is too thin, colloid under the condition of construction is too thin, not enough to compaction the internal air, there was a bubble will easily lead to the construction.

the sewing quality is poor, poor quality of true porcelain rubber products, due to the production process does not pass, the production process, the colloid with a lot of gas, leading to the construction of air bubbles appeared.

filling or transportation, into the air inside, not discharged, glue not according to the proportion of 1:1, not stem and bubble problem.

true porcelain glue heating temperature is high, cause the colloid have bubbles, low temperature in winter, in order to reduce the difficulty of the glue, is often used to true porcelain glue heating way, but if the heating temperature is too high, will be prone to bubbles.

to understand the causes of bubbles and rising, and we'll see how to prevent and solve:

against moisture and dust problem, again, make sure work platform dry clean.

the gap is too small, generally less than 1. 5 mm we don't suggest to do the seam, one is not good to the construction, but make the effect also is not very good. If the owner insist to do, try to stick to & other; Fire makes sweet malt & throughout; The principle of each seam guarantees glue to play full.

construction question, the thickness of the early days, we will also the seam is divided into full fill and the practice of surface layer, according to the construction information feedback later, we generally suggest the owner directly do full fill, ensure the service life of the product already so, also prevented from playing is not enough or fit enough to produce different products construction problems, for example, bubbles and uneven. 。 。

the product quality problem, it is also important for one reason, so we choose as far as possible not to save money and lost a lot of money, so, what kind of small workshops of 3 without the product also don't use as far as possible, don't save this ceramic tile material because it is over, and his more valuable ceramic tile is damaged.

packed into the air and transportation process, this kind of controllable risk accident, we can only give some Suggestions for handling, before construction, take material does screw glue mouth, at the bottom of the down, perpendicular to the ground, to block a few times on the ground, push the bottle at the bottom of the piston, screw on cement, construction.

about heating in winter, the water temperature is 10 to 60 ℃ or so 15 minutes. Specific operation can refer to the seam construction in winter, it's time we GET to the point of what?

added:

the seam pressure bumps in seam pressure after that appear, should be timely treatment. Pressure sewing machine back and forth twice, again filling materials, and seam pressure again.

find bubbles after prick in time, packing pressure again seam, sew by blade pressure effect will be better. The material depth to ensure a minimum of 2 mm.

If you have a need for floor grout sealer tile grout, like , and , you need to be able to find a dependable provider who you can trust when necessary.

Kastar Adhesive Co.,Ltd. endeavors to be valued as an industry leader in client satisfaction, sales growth, product performance, financial strength and profitability.

Through our distribution and marketing competencies, Kastar Adhesive Co.,Ltd. provides creative, customized, solutions for our customers. As a result, we achieve superior profit growth as the tile grout company of choice.