Tile beautiful seams are constructed in winter, and these details can be careless! -Beautiful seam agent factory

There are many issues that need to be considered in the decoration of new houses, among which seasonal factors are also very important. According to the particularity of the winter season, the following details should be paid attention to during the decoration construction process. 1. Humidity Although winter is a relatively dry season, for the southern region, winter is still wet and rainy, with more fog, and indoor humidity is still relatively high. Therefore, for the construction of tile beauty joints during this period, it is still necessary to keep the construction environment dry. Before construction, you need to penetrate into multiple tile gaps to check the dryness of the tile gaps. If only a little muddy dust appears in a few gaps, you can use an air conditioner or a hair dryer to dry the gaps before applying the tile beautifying agent. Although the weather in the north is relatively dry, there may be moisture near doors and windows due to exposure to the outside world. After the construction of the tile beauty joint agent is completed, the original environment of the tile beauty joint agent must also be maintained at the site. At the end of the construction, the tile beauty joint product should not be exposed to moisture before the product is completely cured, otherwise the tile beauty joint product will easily become damp, cause discoloration, fall off and other phenomena. If this phenomenon occurs accidentally, it is necessary to eradicate and add new tile beauty joint agent in time. 2. Temperature The temperature in winter is particularly low, and some areas will produce severe freezing. Therefore, whether it is the storage of the tile beauty joint agent or the construction, the tile beauty joint agent must be insulated and protected. Do not place the tile beauty joint agent in the trunk of the car seat. It should be placed in a room with a constant temperature and stacked in a triangular stack. Before construction, it is necessary to heat the product of the tile beauty joint agent. Soak the tile beauty joint agent product in hot water between °C and °C for about-minute. It is not only necessary to pay attention to the temperature of the product of the tile beauty joint agent, but also the higher temperature requirements for the construction of the tile beauty joint agent during this period. It is best to start construction in a construction environment above °C. If the temperature is not reached, you can use heaters, small suns, air conditioners, warm air and other heating equipment to increase the temperature. And due to the influence of temperature, the curing time of tile beauty joint products will also be appropriately extended according to the temperature. Therefore, it is necessary to reserve enough curing time for tile beauty joint products, and wait until the tile beauty joint products are fully cured. Start to clean up the remaining material. Beauty Suture Factory—Heat Packing. Advantages of the heating package of the United States Suture Factory: full face value;: exquisite workmanship, refusal to shoddy manufacturing;: high-end widened adjustable shoulder strap;: quick-heating heating film, second heating, heating film national standard quality C certification;: stepless temperature control switch, precise temperature control at any time;: detachable design, can be washed, refuse to throw away when dirty;: zipper open cover design, more convenient for taking glue, more effective insulation;: there is a heating compartment in the middle , To ensure that each tube of glue can be heated at the same time, and refuse to heat unevenly;: the thickened cotton layer is all surrounded, and the temperature does not lose. Third, product quality and construction. A lot of attention should be paid to the construction of tile beauty joints. Of course, we must also pay attention to product quality and construction issues. In winter, the temperature is low, and the quality requirements for tile beauty products are also high. Not only are the materials that are well-balanced and easy to discharge, they also need to have a certain degree of antifreeze ability. In addition, the basic advantages of moderate curing time, smooth surface, such as porcelain, anti-fouling and abrasion resistance, are also necessary. 4. Ventilation The dryness of the north makes the north take the advantage of making ceramic tile joints in winter, but the temperature in the north is much lower than that in the south, and the temperature difference between indoor and outdoor is large! Open the door after the tile beauty grout is finished. It is actually a wrong approach to let the tile beauty grout ventilate the windows. In winter, the wind in the north is relatively heavy. Cool breeze blows into the room when the window is opened for ventilation. The tile beauty joint agent that has not fully cured is stimulated by the sudden cooling, which will not only prolong the curing time, but may even cause cracks in severe cases. Phenomena such as cracking of tile beauty joint agent and falling off of tile beauty joint agent. The curing of tile beauty joint agent requires a relatively constant environment, so in the case of large temperature differences in winter, it is best not to open the window, let the tile beauty joint agent completely solidify and stabilize before opening the window for ventilation.
Tile Beauty Seam