Understand beautiful sewing in 1 minute! The master tells you how to avoid these construction problems

An autumn rain and a cold, with varying degrees of rainfall in most areas, the temperature dropped significantly, giving the feeling of early winter. In winter, the low temperature in various regions and the large temperature difference between day and night will have a great impact on the storage and use of the beauty joint agent. In order to ensure the quality of the product and the construction effect, the following matters need to be paid attention to. 1. External environment problems. When the construction temperature is above ℃, if the new house does not have heating, electric heaters can be used to increase the temperature of the indoor construction environment. For construction sites with conditions, the air conditioner can be properly turned on to increase the temperature of the construction site. Properly heating the product when the temperature is too low. Low temperature will increase the viscosity of the epoxy resin, which will worsen the extrudability. Even if it is extruded with a labor-saving glue gun, it will easily cause the AB component to be mixed unevenly, resulting in partial non-drying Or the phenomenon of insufficient hardness. Therefore, it is recommended to put the beauty joint agent into an electric heating bag or hot water (must be sealed) for preheating before construction. The preheating temperature should not exceed ℃ and the time should be controlled within one minute. The preheating time should not be too long, too high temperature will cause the beauty joint agent to sag. When preheating, the discharging port should face down and the bottom face up. The storage temperature must be above ℃, and the storage temperature of the beauty joint agent in winter must be between ℃ and ℃. (Special attention: The storage temperature of the beauty joint agent cannot be changed instantaneously. For example, if the temperature is below (degrees or below), the epoxy resin in the beauty joint agent will crystallize (become small particles). Solid). [Crystalized beauty joint agent can only be scrapped and cannot be used for construction!] During construction near doors and windows, avoid damp cracks. The northern weather is relatively dry, but there is moisture near the windows due to the temperature difference between indoor and outdoor. When constructing near doors and windows, look at it. Look at the gaps and avoid dampness. If the tile gaps are too wet, you can dry the tile gaps first, otherwise the color will change after the beautiful joint construction is damp. Keep the indoor construction environment dry if it rains or rains before the beautiful joint construction In snowy weather, it is best to close the doors and windows to prevent indoor humidity when it rains or snows, which affects the construction progress and construction effect of the beautiful joint. In the southern winter, indoors are humid and foggy, and the humidity is relatively high. Keep the indoor construction environment dry during construction. (Air conditioning can be used to dehumidify) 2. The reasons and solutions of the construction conditions The main components of the material discoloration during construction are epoxy resin, curing agent and pigment. The contact between epoxy resin and curing agent and water will cause a chemical reaction. This will affect the discoloration of the pigment body, which is generally darkened, whitened or transparent. Solution, rainy weather, pay attention to the dryness of the room, reduce the moisture content of the air, pay attention to the closed windows, and open the air conditioner to dehumidify can be appropriately relieved;, gaps Hot air or electric fan can be used to accelerate the evaporation of water vapor. Material shedding, peeling and other phenomena are caused by improper handling of tile gaps and partial lack of coverage; gaps are too small and insufficient adhesion, resulting in shedding; use inferior beauty grouts, No guarantee. During the solution and construction process, clean up the cracks of the tiles without leaving dust or water droplets, and no white powder should appear when using the caulking agent for the primer;, cautiously construct the gaps below MM;, the beauty of the grout factory crystal Porcelain King can be guaranteed for ten years. It will not shrink, collapse or fall off within ten years, and there is no need to worry about any after-sales. It will cause collapse, resulting in uneven thickness. The width of the tile joint is too large and the gap exceeds mm; the temperature is too high in summer, which will cause the material to become thinner. , The heating of the material in winter causes the material to become thinner; during the construction, the material is hit too fast and too thin, and there are different degrees of depression. Solution, do it after the base, it is recommended to use a white base, white will not affect the color of the beauty joint agent; , The material should be placed in a cool place, and the storage temperature is suitable-℃;, heated with warm water, after taking it out, it must be placed flat for one minute, and no direct construction is allowed;, the beauty joint factory, the beauty joint agent, does not flow on the wall, does not collapse on the ground, imported from Germany Raw materials, quality assurance! The main reason for the phenomenon of difficult to hit materials and burst pipes is due to the cold weather. This is the characteristic of epoxy resin. Secondly, it has a certain relationship with the choice of glue gun. The solution is to use -℃ water to heat to Minutes, the epoxy resin becomes thinner when exposed to heat; Choose a good quality glue gun, it is recommended that the manual glue gun or electric glue gun customized by the beauty joint factory. [Note]: The beauty joint agent will adjust different formula ratios according to different seasons, and the environmental temperature difference It is not the quality of the product itself that causes the material to be thick or thin, soft or brittle. (Refer to chocolate for reasons)
Beautiful seam construction problem