Professional manufacturer of tile grout and adhesives with 27 years experience

Where the seam ( This tutorial to ensure a learning will)

2020-12-04

Kastar

132

Small make up to you last time has a brief introduction of the seam some matters needing attention, everyone get to the point? Is ready, just a moment, today small make up the majority of the friends should request to you about how to learn to do the seam, today this tutorial look, everyone is a will to learn.

the preparation for the construction joints

ready for construction tools and products: beauty of two-component special gun, crack-cleaning cone, clean scraper, scraper, seam pressure ball, wallpaper, cloth, wool brush, high power vacuum cleaner.

clean ceramic tile aperture

use clear crack-cleaning cone cracks, crack depth control at about 3 mm, use brush to clear dirt and dust of cracks inside out, and then in the crevice and the whole surface of the ceramic tile with powerful vacuum cleaner dust suction clean ( Crevice have the dust beautiful seam an agent is not strong, there is some dirt on the ground easy to fall in the joint surface, after curing is very ugly) 。

rifle feeding

will be a two-component mixed cement on installed on the seam an agent, be sure to tighten, and then pull out glue gun power lever, will be installed the beauty of mixing cement seam an agent installed on the glue guns. To note here, begin to play out the beauty of about 40 cm seam an agent, don't use scrap directly, because the material of the 40 cm out of curing agents and pigments are not fully discharging, mix proportioning instability can lead to curing effect is not good.

the construction joints method one: the seam pressure ball construction

1. To ceramic tile aperture edge about 2 cm spread the seam on the ceramic tile of special wax, the purpose is to facilitate later remove excess beautiful seam an agent, don't bother oh, waxed work late than your strenuous shovel beauty seam an agent is much more easily.

2. Picked up a glue gun discharging mouth pointed directly at ceramic tile aperture, squeeze out the uniform seam an agent, straight into the gap ( PS: don't squeeze too much, and the ceramic tile flush on both sides of the can, the phone bill is expected to say too much, stick to the sides the beauty of ceramic tile seam an agent will also many, is not easy to clean up late) 。 Said straight fill of the seam an agent to the crevice, friends may be hard to do, after all, everyone is not professional.

3. Fill us with seam pressure ball in seam an agent of roll gap compaction. （ This link banned scrape to evenness with scraper, otherwise it will cause the seam an agent is difficult to clean up, you must use the seam pressure ball)

4. Waiting for the seam an agent solidification, waiting time is commonly: winter 12 hours a day, eight hours in other seasons.

5. Directly with clean shovel shovel gap on both sides of the excess has solidified the seam an agent, the ceramic tile with rag wipe up, this will be accomplished.

method 2: construction method of crepe paper

1. Along the edge of ceramic tile aperture crepe paper, stick good wallpaper knife fixed cross stitch is used after place cover the gap of crepe paper

2. Method with a second, but also with a glue gun uniform and beautiful seam an agent, straight into the crack in the ( In construction of large area, had better overall transverse construction first, and then the longitudinal construction) 。

3. Beauty with a crack in the scraper will be flat seam an agent evenly, immediately after screeding tear (crepe paper Crepe paper must tear before seam an agent to do in the United States, not then it is hard to tear and clean up) 。

4. If ceramic tile is stained with a few beautiful seam an agent, rag wipe up, quickly wipe out it with some alcohol or white vinegar is wiped, wipe the process must be careful, can't meet on the sealant in the gap, this will affect the effect after molding. After clean up will be completed.

today read this tutorial is very simple, is quick to learn, but if you are the first to try to do the seam, small make up or suggest you look for a first test it is not obvious and small place, because the seam once ready later it will be difficult to remove, if you do not mind, then you can want to look at every day dejected, so DIY have risk, before need to be careful.